SUV & TRUCK ACCESSORIES
Call Toll Free

Facebook   Twitter


Join our mailing list!



We proudly accept:





 



 

BurnLounge.com - Buy Music, Sell Music, Online Music Store

Green Beret Foundation

BClick to verify BBB accreditation and to see a BBB report.

(Your shopping cart is empty)

  Home > Ford >

Ford E4OD, 4R100 2WD & 4WD Deep Transmission Pan PML-9323
Ford E4OD, 4R100 2WD & 4WD Deep Transmission Pan PML-9323


 
Alternative Views:


Our Price: $384.00



Product Code: PML-9323


Color:


Machining:


 
Description Technical Specs
 

This PML tranny pan for Ford vehicles fits 1989-2004 Ford 2WD and 4WD with the E4OD or 4R100 transmission. Typical applications are:

  • F250, F350, F450, F550 and F150 Lightning trucks
  • Some full size Broncos
  • Excursion
  • E250 (5.4 V8), E350, E450 vans and motorhomes
  • Lincoln Navigator

If you have a 6.0 diesel, or a 2005 or newer vehicle you'll need a 5R110 TorqShift pan instead of this one.

If you have a 460 V8 and a "Banks Power Pack" kit or an Excursion with a V10, please check carefully for clearance between the exhaust and the transmission pan.

Excursion owners: This pan will clear the frame cross member. If you have a 4WD, you may need to loosen the rear trans mount bolts and jack up the transfer case slightly to ease access to the bolts along the back of the pan.

Temperature Sensor Option

PML Ford tranny pan with temperature sensor holeClick on image for a larger view in a separate window.

This pan has two possible locations for a temperature sensor. One is the boss to the left of the drain hole (as shown in this image) and the other is opposite the drain hole on the passenger's side. These bosses do not come machined. Image at right shows hole drilled on driver's side boss. The bosses accomodate from 1/8 to 1/2 NPT. If you wish PML to machine a hole, please call to order.

About Filters

PML designed this pan to use the stock filter. These are low cost parts and are easily available.

For the filter, this pan has filter supports on the inside. The pick up for the transmission fluid is at the same point with this pan and the stock pan. No filter extension is needed.

About Gaskets

PML recommends a rubber-cork gasket as show in the image.

Rubber cork gasket for Ford tranny pans

PML strongly recommends against reuseable rubber gaskets for several reasons. They nick easily, resulting in leaks. Their hole guides can cause gaps between the pan and the transmission case mating surface. Reuseable rubber gaskets are intended to be used with stamped steel stock pans which flex to provide a seal. Sand cast aluminum pans have machined flanges and DO NOT flex. The rubber-cork gasket is used to seal machined surfaces.

Features

PML Transmission Pan Features

  • Increased oil capacity for cooler temperatures
  • Sand-cast aluminum with raised fins
  • 3/16-inch thick wall construction to add strength to the transmission case
  • 3/8-inch thick gasket flange will not bend when bolts are tightened
  • Machined gasket surface for a secure seal
  • Boss cast into pan can be machined for a temperature sensor
  • Magnetic drain plug for easier, less messy maintenance
  • Mounting hardware provided

NOTE:

If you would like PML to machine your pan for a temperature sensor, there is an additional charge of $40. Please include temperature sensor size in the order notes, or you may order over the phone to insure accuracy. 888-832-5248


Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Ford
   
 

Teaka Toys 1725 San Felipe Road Suite 10 Hollister CA 95023 (831) 630-1545

Company Info | Advertising | Product Index | Category Index | Help | Terms of Use
Copyright © Teaka Toys. All Rights Reserved

Built with VolusionWeb Site Management by Venue Communications, Inc.