Drilling required!
Nothing looks sweeter on the front of your rig than one of N-Fab's custom light bars and sometimes those huge, bulky, black, front-end replacements just aren't needed.  Each Light Bar is designed to compliment other N-Fab products such as Nerf Steps, Desert-Runners and Rear-Runners.  With N-Fab's Light Bar you can fit up to four 9" lights with out a big bulky front end replacement.  Standard color is zinc base coat with a high gloss black powder coat finish for a high quality, corrosion protected, finish that will outlast the competition.  N-Fab offers all of it's products in custom black textured, color-matched or bonded chrome powder coating for an additional charge.

*Check out available offroad lights HERE!
**Color Matching is available.  Please Contact Us for options.
***Textured Black is a special order item and can take up to an additional 7-10 business to ship.

Light Bar Instructions Models C035LB, D025LB, N045LB, F994LB, G035LB, G074LB, and C074LB Hardware Kit Contains: Recommended Tools: 2) 3/8” x 1” Hex Head Bolts 9/16” Socket Wrench 2) 3/8” Washers Black Marker Drill and ½” drill bit Metal punch and Hammer Step 1: Hold the Light Bar up to the face of the bumper where the round mounting brackets are flat against the bumper. Use the top of the bumper to align the Light Bar perpendicular to the ground. Step 2: While the Light bar is positioned on the bumper, mark around the two mounting brackets onto the bumper. Next, remove the light bar and set aside. You should have two circular marks on the bumper. Step 3: Mark a ‘X’ through each circle, this will give you the center. Use a metal punch and hammer to punch a pilot hole through the center of the circle. Step 4: Drill a ½” hole through the pilot marks. NOTE: Make sure the holes are free of metal burs. Step 5: Align the Light Bar mounts to the drilled holes and place a 3/8”x 1” bolt and the 3/8” washer through the back side of the bumper and thread into the light bar bracket. After final positioning, torque each bolt location to 15-20 ft/lbs. NOTE: Removing the bumper may be easier on some models. Model C995LB Step 1: Drill out the two square license plate holes with a ½” drill bit. Step 2: Perform step 5 above. NOTE: Mount the license plate back behind the Light Bar bracket. Model G035LB Hardware Kit Contains: 2) 3/8” x 1” Hex Head Bolts 2) 5/16” x 2” Carriage Bolts 2) 3/8” Washers 2) 5/16” Washers 2) 3/8” Nuts 2) 5/16” Nuts Step 1: Align the two holes in the center bracket of the light bar to the factory license plate holes in the bumper. Next, insert the two 5/16” carriage bolts and the 5/16” nuts and hand tighten. While the light bar is positioned in the bumper, make sure it is level from left to right. Step 2: With a marker, mark around both round mounting brackets on the light bar. Next, remove light bar from the bumper and set aside. Step 3: Perform steps 3-4 above. Step 4: Align the light bar mounts with the drilled holes on the bumper and place the two 5/16” x 2” carriage bolts, 5/16” washers, and 5/16” nuts in the center bracket and hand tighten. Next, start the two 3/8” hex head bolts, 3/8” nuts, and 3/8” washers in the two round bracket mounts on both sides and hand tighten. After final positioning, torque each bolt location to 15-20 ft/lbs. This concludes the installation. Questions? Call 281-880-6322 Products licensed to N-fab Inc. by Fichter Designs are protected by US patent law and International Copy Right law. US Patent #6588783, # 6874801, #7416202. Other patents and continuances pending. N-fab products configuration also protected by International Trade Dress Law. All Design and Patent infringements will be prosecuted to the full extent of the law.

If you are looking for great way to mount a couple lights, while maintaining a stylish look, then check out N-Fab's Light Bars.  N-Fab's new Light Bars are available in 18 different models including applications for Chevy, Ford, Toyota, Dodge, Nissan, GMC, and Jeep.  The unique mounting design allows the applications to be applied to existing factory OEM bumpers.  N-Fab's new light bars are constructed using .095 wall race car tubing that has been treated for corrosion inside and out.  Because of N-Fab's innovative construction, N-Fab light bars require no brackets for installation on most of their models, a simple supplied bolt kit is all that is necessary. There are no modified installation techniques to trucks with body-lift kits.  Standard color availability is coated gloss black but custom colors are available for an additional fee (Please contact Teaka Trucks for color options).